FRAKxxxMV: 2U, 2 Bay, Hot-Swap, Redundant, ATX Power Supply Rack System Product Specification
Product Description
This product is a 2U, 2 bay, 1+1, hot-swap, redundant, ATX power supply rack system incorporating individual power modules offering up to 6 outputs plus a 5V stdby in 360W, 420W, 480W, 540W, 600W, 660W and 750W power module increments. There is even a 24Vdc output to meet CompactPCI and VME platform requirements
Product Features
2U, 1+1, 2 Bay, Rack Mountable ATX Power System
Hot Swap Power Modules for Redundant Operation
Up to 6 Outputs with 5V Standby
Output Options: 3.3V, 5V, 12V, & 24V
AC Input
Voltage Input Range: 90-264Vac
Frequency Range: 47-63Hz
Phase: Single Phase
Typical Input Current: 7.1A at 115Vac input, full load
Power Factor Correction: 0.95 min @ 115Vac, full load
FRAKxxxMV Series Output Selection Matrix
PLEASE CONSULT FACTORY for OUTPUT/POWER CONFIGURATIONS
DC Output Characteristics
Set Point Accuracy: ±1.0% of Output Voltage (Nominal input; full load; 25°C)
Transient Response: Output voltage returns to within 1% in less than 2.5mS for a 50% load change and the peak transient does not exceed 5%
Overshoot: Turn-on and turn-off overshoot should not exceed 10% over nominal voltage
Holdup Time: 16mS
Electrical Characteristics
Switching Frequency: 300KHz Fixed
Efficiency: 85% min (At 20%/50%/100% load and at 115Vac nominal input)
Turn On Delay: 100 to 200mS (To nominal output voltage)
Isolation Voltage (High Voltage Withstand):
Primary to Secondary: 4242Vdc
Primary to Ground: 2800Vdc
Protection
Over Current Limit: 130% maximum for +12V output (V1) and 150% max for 3.3V & 5V outputs
Over-Voltage Setpoint: 108 to 125% of output voltage. Unit latched 1 minute, recycle AC input to reset
Short Circuit: Auto-recovery after short circuit condition is removed and cycle ON/OFF to reset
No-load Operation: No damage or hazardous condition will occur with all the DC output connectors disconnected from the load. The power supply may latch into the shutdown state.
Environmental
Operating Temperature: -10º to +50ºC (Ambient air)
Storage Temperature: -40º to +85ºC
Operating Humidity: 10% to 90% RH, Non-condensing
Storage Humidity: 5% to 95% RH, Non-condensing
Operating Altitude: Sea-level to 16,000 ft.
Conducted & Radiated EMI: Designed to meet EN55022 Level B, CISPR 22 Class B, FCC Part J Class B
Immunity: Designed to CE: EN55024:2010/IEC61000
Safety
Safety Agency Certifications: cUL (cTUVus): UL62368-1, TUV: EN62386-1, CB: IEC62368-1
Cooling
Internally Cooled: Each power module incorporates 2 high reliable DC fans
Mechanical
Enclosure: Metal chassis, enclosure, non-finish.
Outline Dimensions: 150mm X 185mm X 86mm (W X L X H) – not including I/O connectors
Weight: 6.5lbs. (2948 grams)
I/O Cable & Connectors: Standard ATX configuration (Custom cabling/connectors available)
Optional Features, Controls or Alarms
PWR_OK (Power Good Signal)
PS_ON (DC Soft Start)
+5Vsb (Standby Voltage)
I2C/PSMI Output Signals
Note
Product specifications subject to change without notice