FSAK850F: 850 Watt, 1U ATX Industrial Grade Power Supply Product Specification
Product Description
This 850 watt, 1U ATX industrial computer power supply is designed for applications requiring “hot-swap” capability to provide the OEM with a quick, interchangeable power module or for use in a N+1 redundancy configuration. This design utilizes active current sharing and incorporates OR-ing isolation MOFETS to minimize voltage drop.
Product Features
Hot Swap, N+1, Parallelable Power Module
Single Output: 12V (Optional 24V, 28V, 48V or 56V)
Optional N+1 Rack Chassis for up to 3 Power Modules
AC Input
Voltage Input Range: 90-264Vac
Frequency Range: 47-63Hz
Phase: Single Phase
Typical Input Current: 9.1A at 115Vac input, full load
Power Factor Correction: 0.95 min @ 115Vac, full load
Typical Leakage Current: 700uA at 240Vac
FSAK850F Power Module Output Table
Output Table Notes:
1. Total continuous combined output(s) wattage: 850W.
2. Peak current of 12V is 110% of max rated current up to 15mS at 115Vac nominal input.
DC Output Characteristics
Set Point Accuracy: ±1.0% of Output Voltage (Nominal input; full load; 25°C)
Transient Response: Output voltage returns to within 1% in less than 2.5mS for a 50% load change and the peak transient does not exceed 5%
Overshoot: Turn-on and turn-off overshoot should not exceed 10% over nominal voltage
Holdup Time: 16mS
Electrical Characteristics
Switching Frequency: 300KHz Fixed
Efficiency: 85% min (At 20%/50%/100% load and at 115Vac nominal input)
Turn On Delay: 100 to 200mS (To nominal output voltage)
Isolation Voltage (High Voltage Withstand):
Primary to Secondary: 4242Vdc
Primary to Ground: 2800Vdc
Protection
Over Current Limit: 130% maximum for +12V output
Over-Voltage Setpoint: 108 to 125% of output voltage. Unit latched 1 minute, recycle AC input to reset
Short Circuit: Auto-recovery after short circuit condition is removed and cycle ON/OFF to reset
No-load Operation: No damage or hazardous condition will occur with all the DC output connectors disconnected from the load. The power supply may latch into the shutdown state.
Environmental
Operating Temperature: -10º to +50ºC (Ambient air)
Storage Temperature: -40º to +85ºC
Operating Humidity: 10% to 90% RH, Non-condensing
Storage Humidity: 5% to 95% RH, Non-condensing
Operating Altitude: Sea-level to 16,000 ft.
Conducted & Radiated EMI: Designed to meet EN55022 Level B, CISPR 22 Class B, FCC Part J Class B
Immunity: Designed to CE: EN55024:2010/IEC61000
Safety
Safety Agency Certifications: cUL (cTUVus): UL62368-1, TUV: EN62386-1, CB: IEC62368-1
Cooling
Internally Cooled: A single 38mm (Sanyo Denki) high reliable DC fan
Mechanical
Enclosure: Metal chassis, enclosure, non-finish.
Outline Dimensions: 84mm X 280mm X 40mm (W X L X H) – excluding handle & I/O Connectors
Weight: 3.0lbs. (1360 grams)
Input Connector: IEC320 Receptacle
Output Connector: PCB Edge Card (Optional terminal block, consult factory)
Optional Features, Controls or Alarms
PWR_OK (Power Good Signal)
PS_ON (DC Soft Start)
+5Vsb (Standby Voltage)
Note
Product specifications subject to change without notice