500 Watt Single Output Military Grade Power Supply

Product Description

150 Watt Single Output Military Grade DC to DC Converter This unit is a 500 watt, single output, military grade power supply designed for electronic systems operating in harsh environments (shock and vibration) and extreme temperature conditions. It is conduction cooled providing a -55° to +85° C operating temperature range. This highly reliable design will meet or exceed all applicable military standards including MIL-STD-810D & MIL-STD-461D.

Product Features

Meets MIL-STD-461D
Meets MIL-STD-810D
Wide Range Input: 90-265Vac
Wide Range Frequency: 47-415Hz
Operating Temperature Range: -40º to +85º C

AC Input

Voltage Input Range: 100-150VAC (115Vac nominal input)
Frequency: 400Hz (47-415Hz)
Phase: Three Phase
Power factor correction: 0.99 @ Full Load

Output Selection Guide

Model #:	Voltage	Max Current	Regulation	Ripple
M115-X-1	3.3Vdc	106 Amps	±3%	50mV pk-pk
M115-X-2	5.0Vdc	80 Amps	±3%	50mV pk-pk
M115-X-3	9.0Vdc	45 Amps	±3%	120mV pk-pk
M115-X-4	12Vdc	37.5 Amps	±1%	120mV pk-pk
M115-X-5	15Vdc	33.3 Amps	±1%	150mV pk-pk
M115-X-6	19Vdc	26.3 Amps	±1%	150mV pk-pk
M115-X-7	24Vdc	20.8 Amps	±1%	240mV pk-pk
M115-X-8	28Vdc	17.8 Amps	±1%	240mV pk-pk
M115-X-9	36Vdc	13.8 Amps	±1%	240mV pk-pk
M115-X-10	48Vdc	10.4 Amps	±1%	240mV pk-pk

Note: Alternate output voltages are available, consult factory for availability.

DC Output Characteristics (Floating)

Output Power: 500 Watts (maximum continuous power, may require derating for some low voltage outputs)
Line Regulation: ±5.0% Typical
Load Regulation: ±2.0% Typical (No load to full load; nominal input)
Output Ripple/Noise: 1% Typical (pk-pk; nominal input; full load; 20MHz bandwidth)
Set Point Accuracy: ± 1.0% of Output Voltage (Nominal input; full load; 25°C)
Transient Response: Output voltage returns to within 1% in less than 2.5mS for a 50% load change and the peak transient does not excess 5%.
Overshoot: Turn-on and turn-off overshoot should not exceed 5% over nominal voltage.

Electrical Characteristics

Switching Frequency: 250KHz Fixed
Efficiency: 85% Typical (Measuring at 115Vac and at full load)
Turn On Delay:1.5 second maximum at 120 VAC
Isolation Voltage: 500V between input and output. 100V between input and case.
Isolation Resistance: 10Mohms (Input to output)
Temperature Regulation: +/-2.0%/ºC (+/-.005%/ ºC max; over operating temp range)

Protection

Over Current Limit: ~115 to 120% of maximum rating. Hiccup, continuous.
Over-Voltage Setpoint: ~115% of nominal main. Unit latched 1 minute, recycle AC input to reset at 25°C.
Short Circuit: Auto-Recovery after short circuit condition is removed.
Over temperature Protection: Shutdown at baseplate temperature of +105°C (±5°C) Automatic recovery at baseplate temperature lower than +95°C (±5°C)

Environmental

Operating Temperature: -55º to +85º C (baseplate)

Storage Temperature: -55º to 125º C
Operating Humidity: 5% to 90% RH, Non-condensing
Storage Humidity: 5% to 95% RH, Non-condensing
Operating Altitude: Sea-level to 40,000 ft. in pressurized environment
Sock & Vibration Standards: MIL-STD-810D
Conducted EMI: MIL-STD-461D
Cooling: Conduction cooled, coldplate mounting

Reliability

150,000 hours, calculated per MIL-STD-217F at +85°C baseplate, ground fixed.

Mechanical

Outline Dimensions: ~1.1" X 3.5" X 5.6" (H X W X L) – not including I/O connector
Weight: ~1.28 lbs. (580 grams)
AC Input & Output Connector: 37 Pin D-Sub M24308/24-40 or equiv.

Additional Features, Controls or Alarms

Remote External Synchronization Capability In/Out
TTL Logic Enable
Remote Sense

Notes

Some specifications have not been tested for actual compliance and can not be guaranteed to meet 100% compliance during system testing.
The information and specifications contained in this document are believed to be correct and accurate at the time of publication. DSC Power Solutions, Inc. accepts no responsibility for consequences