2000VA Military Grade Uninterruptible Power System

Product Description

2000VA/1500W, Military Grade Uninterruptible Power System This unit is a 2000VA/1500W, military grade, uninterruptible power system designed for electronic systems requiring back up power which are operating in harsh environments (subject to abnormal shock and vibration) and demanding temperature conditions. This UPS is a ruggedized, on-line, double conversion topology with an input isolation transformer to provide input to output isolation during normal operation and during bypass mode. This highly reliable design will meet or exceed all applicable military standards including MIL-STD-1399 (Section 300A).

Product Features

True On-line, Double Conversion Topology
2000VA/1500W Capacity
MIL-STD-461D Compatibility
Ruggedized to withstand Shock & Vibration
Wide Range Input: 90-265Vac
Wide Range Frequency: 48-64Hz
Operating Temperature Range: 0º to +52º C

AC Input

Voltage Input Range: 84-165VAC or 180-260VAC (Selectable)
Frequency: 50/60Hz
Phase: Single Phase, 2 wire plus ground
Power factor correction: >0.98 @ Full Load
Input Isolation: Galvanically isolated from output and chassis (>1MΩ at 600VDC). Total capacitance between input and chassis is less than 0.02uf per line. Both input wires may be “hot” I.A.W MIL-STD-1399.
Leakage Current: <2mA (130dB Input Isolation Transformer)
Current Waveform: Sinusoidal with harmonic content of less than 2.5% for harmonics between 2fo to 32fo and less than 100%/N for harmonics between N=32 and 20kHZ (I.A.W MIL-STD-1399 Section 300A).
Line Impedance: Up to 5 ohms between 100Hz and 200Hz (I.A.W MIL-STD-1399 Section 300A).
Input Spike Protection: 200 joules clamping

AC Output

Rating: 2000VA/1500W
Output Voltage: 115Vac, ±3%, grounded neutral
Frequency: 60Hz ±0.2%
Phase: Single Phase, 2 wire plus ground
Waveform: Sinusoidal. THD <2% (linear load), <4% (non-linear load)

Internal Battery

Back Up Time: Full rated output for at least 10 minutes.
Type: Internal, encapsulated, sealed maintenance-free, lead-acid.
Charger: Low ripple, regulated voltage float-charger with current limiting and temperature compensation. Fully charging the battery within 3 hours after 10 minute discharge.
Battery Protection: Battery is protected from over-discharge by an internal protection circuit (to avoid battery damage due to prolonged power outage).
Monitor: Battery charge level and internal impedance are monitored by the UPS micro-controller.

Environmental

Operating Temperature: 0º to +52º C
Storage Temperature: -40º to 72º C (non-operating)
Operating Humidity: Up to 95%
Operating Altitude: Sea-level to 10,000 ft. (Non-operating up to 40,000 ft.)
Mechanical Shock: When packed, withstands the free fall drop and edgewise drop IAW Methods 5007.1 and 5008.1 Federal Test Method standard 101C. When operating, withstands the high-impact shipboard shock IAW MIL-S-901D, Grade A, Class II, Type B
Vibration Standards: When operating, withstands Type I vibration IAW MIL-STD-167-1. The UPS will endure a sweep of 1.5g sinusoidal vibration from 5 to 50 HZ for a total duration of 2 hours and random vibration IAW MIL-STD-810D, Cat. 9, Proc. I (test condition I-3.2.11 Fig. 514.3-34).
Acoustic Noise: Less than 48dBA

EMI/EMC

FCC: Meets Title 47, Part 15, Class A
MIL-STD-461D: Meets RE101, RE102, CE101, CE102, CS101, and RS103
ESD: All I/O lines are protected from ESD

Mechanical

Metal Enclosure: 4U, 19” Rack Mountable Chassis with Internal Fan
Outline Dimensions: 7" X 19" X 21" (H X W X L)
Weight: ~156 lbs.
AC Input: MS3102A22-2P (Mil Compliant, Circular Style Connector)
AC Output Connector: MS3102A24-10S (Mil Compliant, Circular Style Connector)
Dry Contact: M24308\24-25 (J3: 9 Pin D-Sub)
RS232: M24308\23-25 (J4: 9 Pin D-Sub)
Remote Switches: M24308\24-26 (J5: 15 Pin D-Sub)

Indicators, Controls or Alarms

Bar Graph for Load Level Display
Bar Graph for Battery Charging Level
LED Status Lamps: Output OK, On Battery & Standby
LED Warning Lamps: Low Battery, Input Fail, Output Fail, Overload Shutdown, Overtemp Warning & Shutdown
LED Battery Test Lamps: Battery Passed or Battery Fail
Audible Alarm:
On/Off Switch: Main switch located on front panel. UPS has two double-pole contactors, one at the input connector and one at the output connector.
Remote On/Off: Two on/off pins will shut down UPS by opening input and output contactors.

Interface

Discrete: Four dry contacts to signal: UPS On (Output OK), Battery Voltage Low, Input Power Loss (Battery Operation), & Fault Detect.
Serial (RS-232): User programmable options for remote communication with UPS status signals and commands.
Remote On/Off Power Control: Jumper selected

Notes

The information and specifications contained in this document are believed to be correct and accurate at the time of publication.